|
|
|
|
|
TRY OUT OUR CL FREE POOL SYSTEM - FREE FOR 90 DAYS. |
 Email to a Friend
Bookmark & Share
|
| | Chlorine Free Fiberglass Pools and Spas | | | |
CL Free Water Systems Fiberglass Pool/Spa System sanitizes and protects your inground Viking fiberglass Leisure swimming pool water and gives you a chlorine and salt free swimming experience. The system eliminates chlorine, chemicals and other impurities from your fiberglass pool water. As it freshens and sanitizes your swimming pool water, the system also kills and protects your swimming pool water from bacteria and algae by adding copper ions and oxidizing carbon based impurities in the water with titanium created OH. The CL Free Water Systems Viking Fiberglass Pool/Spa System significantly reduces the calcium buildup in the fiberglass swimming pool equipment and along the Viking pool and spa water lines.
1. The power settings for the Oxidation and Ionization functions are independent. This provides flexibility and total control. Other units tie both sets of functions to each other providing no flexibility or independent control.
2. Oxidation and Ionization functions can be energized at the same time. Other units make you manually select and switch between which functions/plates are energized.
3. LEDs flash at different frequencies to indicate that the corresponding functions have been activated and at what power level. Faster flash means higher power.
4. LEDs alternate color (red and green) to indicate that the polarity of the functions/plates have been switched. This swap balances the copper plate usage and helps keep the plates clean.
5. Copper Ionization has a built-in startup setting (to quickly bring your Leisure fiberglass pool/spa up to the desired copper level) and 8 different maintenance settings (to maintain the desired copper level). If the Leisure fiberglass swimming pool system is run non stop, after 24 hours it resets itself and begins its daily cycle again.
6. Based on the Controller pH setting, the pH sensor determines if pH adjustment should be made or not. As pH reduction is needed,co2 is injected in metered ,controlled regular intervals.
7. Your pool/spa's pH is displayed every 30 seconds on the controller's readout.
8. pH calibration is a snap. Push the calibrate button 2 seconds, enter the pool's actual pH, press the button again, you're done.
9. The system consists of a CL Free Systems Oxidation Chamber with titanium and copper plates, Fiberglass Pool/Spa controller, pH sensor, flow meter controlled co2 regulator, UL approved power supply and wiring harness.
 |
|
 |
|
co2 Injector |
Fiberglass Pool/Spa Controller |
In ground Pool System Installation |
CONTACT US FOR A FREE CONSULTATION. THANK YOU.
http://www.clfree.com
|
|
|
Operation, Pool/Spa System Ionization (Copper)
If the Controller’s Ionization setting is 9, the system runs full power to the copper plates as long as the swimming pool filter equipment is running. Use this setting to initially get the fiberglass pool up to the desired copper level as quickly as possible.
If the Controller’s Ionization setting is 0, no power is applied to the copper plates.
If the Controller’s Ionization setting is 1 thru 8, the swimming pool system applies power to the copper plates for the first hour only. The lower number provides lower power, higher number, higher power. Use these settings to maintain the desired copper level in the pool. Determining the correct maintenance setting will require every other day copper level testing for the first two weeks, and weekly thereafter.
At regular intervals, plate polarity is switched to ensure equal wear of the plates. The LEDs change colors (red and green) to indicate the polarity change.
Oxidation
If set to 0, no power is applied to the titanium plates.
If set to 1 thru 9, energizes the titanium plates as long as the unit is powered. Run this setting as high as possible. If the fiberglass swimming pool water gets cloudy, skip oxidation one day, reduce the setting and resume oxidation.
At regular intervals, plate polarity is switched. The LEDs change colors (red and green) to indicate the polarity change. This also helps keep the plates clean.
pH control
At regular intervals, the system takes a pH reading and then dispenses pH reducer as needed to maintain the pool/spa’s pH.
The pH reading cycle takes 12 seconds, during which the Oxidation/Ionization LEDs are turned off. This indicates the pH reading cycle is taking place. Pressing the up pH button will initiate a pH reading cycle.
Based on the readings, the swimming pool system decides if the sensor is working correctly or not. If the pool system decides the sensor is bad, or that the readings are too high or too low, the display flashes the appropriate error code which indicates the the system and/or swimming pool needs attention.
|
"my daddy loves me, he takes me swimming in Chlorine | | |
|
|
|
|
|
|
|
|
Oakland, Livingston, Macomb, Washtenaw, and Wayne counties. Birmingham, 48009, Michigan, West Bloomfield, 48324, 48323 Michigan Highland, Michigan 48357, 48356 Northville, Michigan, 48167 Milford, Michigan, 48380, 48381 Bloomfield, Michigan, 48301,48302,48304 White lake, Michigan, 48383 Brighton, St. Clair Shores. 48080, 48081,48082. Michigan, 48116 Wixom, Michigan, 48393 Hartland, Michigan, 48353 Bloomfield Hills, Michigan, Fenton, michigan 48430 Rochester Hills, Michigan, 48306,48307,48309,48306,48309, 48442 South Lyon, Michigan, 48178 Union Lake, Michigan, 48387 Clarkston, Michigan, 48346,48348 Ann Arbor, Michigan 48103, Birmingham, Michigan, 48009
